Professional Flooring Supply
Choose Your Options

Product Listing

Sort by
Products per page
 ProductStockPrice 
New UZIN Reinforcing Fibers can be used to improve impact resistance and control shrinkage of any UZIN self-leveling compound when used on demanding substrates. Use for unsound substrates in renovation work. Reduces cracking of the leveling compound when used on unsound substrates.Easy to incorporate : 1 bag of fibers to 1 bag of leveling compound. Interior use onlyUzin Reinforcing Fibers (Pk)
Login
for
Availability
Login
for
Price
A Portland cement-based, polymer-modified, self-leveling underlayment that replaces traditional backer board, providing a flatter, smoother surface faster and easier for installing tile and stone. ARDEX Liquid BackerBoard can be used over interior wood or concrete subfloors. It eliminates cutting, fitting, gluing, taping, fastening and the many other steps required with bulky, hard to transport traditional backer board. The optimal tiling surface!Ardex LBB Liquid Backerboard Underlayment - 50 Lb
Login
for
Availability
Login
for
Price
ARDEX LU 100 Self-Leveling Underlayment is a blend of high strength cements and powdered polymers used to repair existing above-grade floors prior to the installation of new floor coverings. Installs directly over well-bonded VCT, and existing patching, leveling or fill materials where complete removal is not an option.Ardex LU100 Self Leveling Underlayment - 50 Lb
Login
for
Availability
Login
for
Price
ARDEX TRM Transportation Repair Mortar is a formable, pourable, pumpable structural repair mortar for deteriorated exterior and interior concrete above, on or below grade. ARDEX TRM is fast-setting, allowing foot traffic in just 2 hours, and vehicular traffic in as little as 6 hours. It is also easy to apply and readily bonds to concrete. The resulting patch has low shrinkage, resists delamination and produces a surface suitable for normal commercial, institutional and multi-unit residential traffic.Ardex TRM Transportation Repair Mortar - 50 Lb
Login
for
Availability
Login
for
Price
Use with ARDEX UI 740 FLEXBONE Uncoupling Membrane. Along the perimeter walls and penetration of the covering, use ARDEX UD 146 Edge Insulation Strips with a self-sticking adhesive foot.Ardex UD 146 Edge Insulation Strip 65.5'
Login
for
Availability
Login
for
Price
Use with ARDEX UI 740 FLEXBONE Uncoupling Membrane. The joints in the mats are to be covered with self-adhesive ARDEX UD 156 Movement Joint Tape to protect against the entry of mortar and grout.Ardex UD 156 Movement Tape 164'
Login
for
Availability
Login
for
Price
Use with ARDEX UI 740 FLEXBONE Uncoupling Membrane. The joint areas of the individual lengths are secured by overlapping the mesh weave at the sides. Joint areas at the top ends as well as any cut areas are bonded using the self-adhesive ARDEX UD 158 Seam Reinforcement Mesh Strip.Ardex UD 158 Seam Reinforcement Tape - 32.5 Ft
Login
for
Availability
Login
for
Price
Ardex UI 720 Flexbone Floating Uncoupling Membrane - 215 SfArdex UI 720 Flexbone Floating Uncoupling Membrane - 215 Sf
Login
for
Availability
Login
for
Price
Ardex UI 740 Flexbone Uncoupling Membrane - 215 SfArdex UI 740 Flexbone Uncoupling Membrane - 215 Sf
Login
for
Availability
Login
for
Price
LockDown is a versatile,100% solids, epoxy resin system that can be used as a vapor suppression, broadcast priming and crack repair. LockDown is designed for use over existing concrete where the level of moisture emissions from the slab exceeds the maximum allowed by the manufacturer of the finished floor covering. It also can be used on new projects where schedules do not allow for freshly poured concrete to fully cure.CMP Lockdown 100% Solids Vapor Suppression 2.5 Gal
Login
for
Availability
Login
for
Price
PolyBond is a water based, high solids, acrylic emulsion admixture and adhesion promoter specifically designed for use with CMP Engineered Cements. When exposed to moisture it will not re-emulsify making it ideal for both interior and exterior applications.CMP PolyBond Latex Admix - 1 Gal
Login
for
Availability
Login
for
Price
PolyBond is a water based, high solids, acrylic emulsion admixture and adhesion promoter specifically designed for use with CMP Engineered Cements. When exposed to moisture it will not re-emulsify making it ideal for both interior and exterior applications.CMP PolyBond Latex Admix - 5 Gal
Login
for
Availability
Login
for
Price
AS-100 is a premium interior / exterior acrylic primer designed for use with CMP’s line of underlayment’s and toppings. AS-100 can be used on a wide variety of substrates including concrete, wood, well bonded VCT, Epoxy, Gypsum underlayment, cutback and other adhesive residues not affected by water. AS-100 is quick drying and with a unique ability to bond to both porous and non-porous substrates.CMP Premium Acrylic Based Bonding Agent And Primer 5 Gal
Login
for
Availability
Login
for
Price
AS-100 is a premium interior / exterior acrylic primer designed for use with CMP’s line of underlayment’s and toppings. AS-100 can be used on a wide variety of substrates including concrete, wood, well bonded VCT, Epoxy, Gypsum underlayment, cutback and other adhesive residues not affected by water. AS-100 is quick drying and with a unique ability to bond to both porous and non-porous substrates.CMP Premium Acrylic Based Bonding Agent And Primer Gal
Login
for
Availability
Login
for
Price
Perma Base 1/2" Concrete 3' x 5'Perma Base 1/2" Concrete 3' x 5'
Login
for
Availability
Login
for
Price
Perma Base 1/4" Concrete 3' x 5'Perma Base 1/4" Concrete 3' x 5'
Login
for
Availability
Login
for
Price
Perma Base 7/16" Concrete 3' x 5'Perma Base 7/16" Concrete 3' x 5'
Login
for
Availability
Login
for
Price
Schluter Ditra Drain 10 MM 108Sf Thin Bed Drainage MembraneSchluter Ditra Drain 10 MM 108Sf Thin Bed Drainage Membrane
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT integrates customizable, comfortable electric floor warming with the functions associated with DITRA: uncoupling, waterproofing, vapor management and support to ensure a long lasting installation. Floor Warming-DITRA-HEAT combines the flexibility of loose heating cables with the ease of installation of mat systems. Cables can be placed wherever heat is desired, without creating height differences in the floor. Self-leveling compounds are not required to encapsulate the cables, significantly reducing installation time and effort.Uncoupling-Tile has been successfully installed for thousands of years by incorporating an uncoupling layer, or forgiving shear interface, within the tile assembly. DITRA-HEAT provides uncoupling through its geometric configuration, which allows for in-plane movement that effectively neutralizes the differential movement stresses between the substrate and the tile, thus eliminating the major cause of cracking and delaminating of the tiled surface. Vapor Management-The free space on the underside of DITRA-HEAT provides a route for excess moisture and vapor to escape from the substrate that could otherwise cause damage to the tile covering above. Thus, DITRA-HEAT effectively manages moisture beneath the tile covering.Support/load distribution-When placed on a solid foundation, columns or pillars can support tremendous loads. The same physical principle applies to DITRA-HEAT installations. Column-like mortar structures are formed in and between the studs on the surface of the matting. Loads are transferred from the tile covering through these column-like mortar structures to the substrate. Since DITRA-HEAT is virtually incompressible within the tile assembly, the advantages of uncoupling are achieved without sacrificing point load distribution capabilities.Schluter Ditra Heat Uncoupling Water Proofing Memb 3'3" x 41'1" RL
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT-E-HK are twisted pair heating cables designed for integration with the DITRA-HEAT uncoupling membrane in interior floor warming applications. Cables snap into the membrane; clips and fasteners are not required. No self-levelers required to encapsulate the cables; installation time significantly reduced. No return to thermostat required. Produces virtually zero electromagnetic fields. 120 V and 240 V options available in a variety of lengths.Schluter Ditra Heat E HK Heating Cable 212.9 Lf 815W Total Pwr
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT-E-HK are twisted pair heating cables designed for integration with the DITRA-HEAT uncoupling membrane in interior floor warming applications. Cables snap into the membrane; clips and fasteners are not required. No self-levelers required to encapsulate the cables; installation time significantly reduced. No return to thermostat required. Produces virtually zero electromagnetic fields. 120 V and 240 V options available in a variety of lengths.Schluter Ditra Heat E HK Heating Cable 336.9 Lf 1290W Total Pwr
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT-E-HK are twisted pair heating cables designed for integration with the DITRA-HEAT uncoupling membrane in interior floor warming applications. Cables snap into the membrane; clips and fasteners are not required. No self-levelers required to encapsulate the cables; installation time significantly reduced. No return to thermostat required. Produces virtually zero electromagnetic fields. 120 V and 240 V options available in a variety of lengths.Schluter Ditra Heat E HK Heating Cable 70.5 Lf 270W Total Pwr
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT-E-HK are twisted pair heating cables designed for integration with the DITRA-HEAT uncoupling membrane in interior floor warming applications. Cables snap into the membrane; clips and fasteners are not required. No self-levelers required to encapsulate the cables; installation time significantly reduced. No return to thermostat required. Produces virtually zero electromagnetic fields. 120 V and 240 V options available in a variety of lengths.Schluter Ditra Heat E HK Heating Cable 88.2 Lf 338W Total Pwr
Login
for
Availability
Login
for
Price
DITRA-HEAT-E-RT is a programmable touchscreen thermostat used to control the DITRA-HEAT-E-HK heating cables (either 120 V or 240 V). The thermostat features a 5 mA built-in ground fault circuit interrupter (GFCI) with indicator light and includes a floor temperature sensor. DITRA-HEAT-E-RT is operated via LCD touchscreen controls and features a pre-set schedule for convenience, which may be programmed to fit any schedule. Two heating cables may be connected to the thermostat, up to the total heating load limit of 15 amps. The DITRA-HEAT-E-RR power module may be used in conjunction with the thermostat when the heating load exceeds 15 amps (e.g., in large floor applications) to maintain a single point of control.Schluter Ditra Heat New Programmable Touch Thermostat Bright White
Login
for
Availability
Login
for
Price
Schluter-DITRA-HEAT integrates customizable, comfortable electric floor warming with the functions associated with DITRA: uncoupling, waterproofing, vapor management and support to ensure a long lasting installation. Floor Warming-DITRA-HEAT combines the flexibility of loose heating cables with the ease of installation of mat systems. Cables can be placed wherever heat is desired, without creating height differences in the floor. Self-leveling compounds are not required to encapsulate the cables, significantly reducing installation time and effort.Uncoupling-Tile has been successfully installed for thousands of years by incorporating an uncoupling layer, or forgiving shear interface, within the tile assembly. DITRA-HEAT provides uncoupling through its geometric configuration, which allows for in-plane movement that effectively neutralizes the differential movement stresses between the substrate and the tile, thus eliminating the major cause of cracking and delaminating of the tiled surface. Vapor Management-The free space on the underside of DITRA-HEAT provides a route for excess moisture and vapor to escape from the substrate that could otherwise cause damage to the tile covering above. Thus, DITRA-HEAT effectively manages moisture beneath the tile covering.Support/load distribution-When placed on a solid foundation, columns or pillars can support tremendous loads. The same physical principle applies to DITRA-HEAT installations. Column-like mortar structures are formed in and between the studs on the surface of the matting. Loads are transferred from the tile covering through these column-like mortar structures to the substrate. Since DITRA-HEAT is virtually incompressible within the tile assembly, the advantages of uncoupling are achieved without sacrificing point load distribution capabilities.Schluter Ditra Heat Sheets Uncoupling Water Proofing Memb 3'3" x 2'7"
Login
for
Availability
Login
for
Price

Showing 1 - 25 of 45 Results

Technical

About Us

Policies

Contact Us
Store Locator

  • Connect With Us:

FSC Approved

Copyright © 2018 Professional Flooring Supply.  All rights reserved.